Hainbuch centroteX S Скачать руководство пользователя страница 56

Страница: 56 / 60

Quick change-over system centroteX S
Faults

Order h49 7144.907-333

Fault

Possible cause

Remedial action

Remedied by

Geometry
deviation on the
workpiece

Concentricity error
on the clamping
device

Check the concentricity of the
quick change-over system and the
clamping device, and correct if
necessary

Skilled special-
ist

Top run-out error
on the clamping
device

Check top run-out on the quick
change-over system and the
clamping device and, if required,
clean their mating surfaces

It is no longer pos-
sible to install the
quick change-over
unit / quick
change-over
adapter

Defective axial
strokes in the quick
change-over sys-
tem

See fault »Incorrect axial strokes
in the quick change-over system«

It is difficult to take
down the quick
change-over unit /
quick change-over
adapter

Dirt on the quick-
release screws

Use force to release the quick
change-over unit / quick change-
over adapter and clean the quick-
release screws

Skilled special-
ist

Table 7:

Fault table

13.3 Commissioning after a fault has been remedied

After the fault has been remedied, perform the following
steps to recommission it:

1. Reset the emergency stop equipment.

2. Acknowledge the fault on the control unit of the machine

tool.

3. Ensure that no-one is in the danger area.

4. Start the machine tool.

Содержание centroteX S





























































Результаты поиска

Содержание centroteX S

Отзывы:

Похожие инструкции для centroteX S

Бренды по названию

Популярные бренды

Hainbuch centroteX S, Руководство по эксплуатации

Результаты поиска

Содержание centroteX S

Отзывы:

Похожие инструкции для centroteX S

Бренды по названию

Популярные бренды