Hainbuch centroteX S Скачать руководство пользователя страница 20

Страница: 20 / 60

Quick change-over system centroteX S
Technical data

Order h49 7144.907-333

3 Technical data

INFORMATION

The technical data for the clamping device are item-
ized in the operating instructions for the clamping de-
vice [see operating instructions for the clamping de-
vice].

In addition to these operating instructions, also read
and follow the operating instructions for the relevant
clamping device.

3.1 General information

ize

imens

ion

k [

th]

[

𝒎𝒎

]

imum

[

𝒎

𝒊𝒏

−

𝟏

]

xial

lamp

ing

orce

𝑭

𝒂𝒙

𝒎𝒂

𝒙

[

𝒌𝑵

]

ial

lamp

ing

orce

𝑭

𝒓𝒂

𝒅

𝒎𝒂

𝒙

[

𝒌𝑵

]

Wei

[

𝒌𝒈

]

alancing qua

𝑮

𝒏

plane

165

Ø 224.0 x 136.6

5000

21.4

4/1

Table 1:

Technical data

3.2 Performance values

NOTE

Material damage to the products use and/or to the
machine tool caused by exceeding the maximum
performance values!



Do not exceed the maximum performance values
[see »General information« chapter].



On all products used, do not exceed the lowest of
the maximum performance values.



Only use product in machine tools with the same
performance values.

INFORMATION

Details of maximum performance values can be found
on each product.

If, due to abrasive wear, those performance values
are no long legible, refer to the operating instructions.

Содержание centroteX S





























































Результаты поиска

Содержание centroteX S

Отзывы:

Похожие инструкции для centroteX S

Бренды по названию

Популярные бренды

Hainbuch centroteX S, Руководство по эксплуатации

Результаты поиска

Содержание centroteX S

Отзывы:

Похожие инструкции для centroteX S

Бренды по названию

Популярные бренды