Haier HLTD500AGW Скачать руководство пользователя страница 34

Страница: 34 / 35

SERVICE MANUL

Model No.HLTD500AGW

Issue

Rev.

- 33 -

Chapter 10 Maintenance

Lint filter needs to be cleaned before

or after each use for your unit to

operate at optimum efficiency. The

filter can be removed by pulling on

the tabs located on the inside of the

dryer door. The filter may be washed

or vacuumed. Remove the excess

water from the filter by gently shaking the filter. This will remove dust and

particles trapped in the filter. Lint built up in screen will restrict airflows, which

causes longer drying times. After cleaning, slide the filter back in place. Do not

use your dryer without the lint filter.

Do not use any type of spray cleaner when cleaning the interior.

r. If dryer drum becomes stained,

clean the drum with damp cloth. Remove any residue before drying next load.

r. Do not use harsh or abrasive

cleaners, as this could damage the dryer.

the duct and the vent on a regular basis to avoid clogging which could

affect the efficiency of the dryer.

Lint Filter

Содержание HLTD500AGW




































Результаты поиска

Содержание HLTD500AGW

Отзывы:

Похожие инструкции для HLTD500AGW

Бренды по названию

Популярные бренды

Haier HLTD500AGW, Руководство по обслуживанию

Результаты поиска

Содержание HLTD500AGW

Отзывы:

Похожие инструкции для HLTD500AGW

Бренды по названию

Популярные бренды