background image

5

Dry sensor : (feature only active in auto dry cycle)

End of cycl e signal:

Lint filter:

Leveling legs:

Your dryer also has the following features for your convenience:

C

New features

Thi

      Your dryer is equipped with an audible signal that alert you every time when the dryer load is

finished drying.

      All dryers come with a lint filter that needs to be cleaned before or after every use.

s senses temperature in the drum.The dryer will automatically shut itself off.

Your dryer has four leveling legs which are located in the front and rear corners of your

dryer. After properly placing your dryer or by turning them counter clockwise to lower your dryer.

Leveling legs can be adjusted by turning them clockwise to raise your dryer or by turning

them counter clockwise to lower your dryer.

6) Lint filter

It is a kind of wearing part, made of filter screen frame and screen cloth by one-time plastic injection.

When taking off the lint filter, please do not squeeze the screen cloth by force to avoid damaging the
cloth. At the same time, please clean it in time after each usage.

Service Manual

 

 

Model No. CGDE480BW

Issue

Rev.

Содержание CGDE480BW

















Отзывы: