Haier 1U50S2SJ2FA-1 Скачать руководство пользователя

Страница: 35 / 75

Service Diagnosis

10.4.1

Thermistor or Related Abnormality

Indoor Display

E1: Room temperature sensor failure

E2: Heat-exchange sensor failure

Outdoor display

LED1 flash 10 times Defrost temperature sensor failure

LED1 flash 11 times Suction temperature sensor failure

LED1 flash 12 times Ambient temperature sensor failure

LED1 flash 13 times Discharge temperature sensor failure

The temperatures detected by the thermistors are used to determine thermistor errors

When the thermistor input is more than 4.92V or less than 0.08V during compressor

operation.

Note: The values vary slightly in some models

Faulty connector connection

Faulty thermistor

Faulty PCB

* Caution: Be sure to turn off power switch before connect or disconnect connector,
or else parts damage may be occurred.

Thermistor resistance inspection method:

Remove the connector of the thermistor on the PCB, and measure the resistance of thermistor using tester. The

relationship between normal temperature and resistance is shown in the value of indoor thermistor.

Malfunction

Decision

Conditions

Method of

Malfunction

Detection

Is it normal?

Yes

Is it normal?

Yes

Check the connector connection.

Replace the indoor PCB

Replace the thermistor

Thermistor resistance check

Correct the connection

Supposed

Causes

Trouble

shooting

Содержание 1U50S2SJ2FA-1












































































Результаты поиска

Содержание 1U50S2SJ2FA-1

Отзывы:

Похожие инструкции для 1U50S2SJ2FA-1

Бренды по названию

Популярные бренды

Haier 1U50S2SJ2FA-1, Руководство по обслуживанию

Результаты поиска

Содержание 1U50S2SJ2FA-1

Отзывы:

Похожие инструкции для 1U50S2SJ2FA-1

Бренды по названию

Популярные бренды