background image

Functions and control 

17 

 Domestic air conditioner 

When refrigerating, it is needed to satisfy 

F-MIN-d(compressor’s Min_hz)< F<F-MAX-d(compressor’s Max_hz)

When heating, it is needed to satisfy 

F-MIN-r (compressor’s Min_hz)< F<F-MAX-r (compressor’s Max_hz)

PID control : 

The innital frequency Sn is determined by Pn . We can calculate Hzoutf according to the value of Kp ,Ki ,Kd, 

Out_gain,Pn.Then , Fn = Sn + Hzoutf. The value of Fn is calculated in each sample time (60 seconds),and Fn is 

adujusted according to previous frequency of Sn and filtered output of Hzoutf. 

7.1.2 The outdoor fan control (Exchange fan) 

When the fan is changed among every airflow speed (including stop blowing), in order to avoid the 

airflow speed from skipping frequently, it must be kept under each mode for over 30 seconds, and then 

it can be changed to another mode (when refrigerating, the time is changed to 15 seconds). 

7.1.2.1 The outdoor fan control 

Within three minutes of compressor starting, the compressor is controled according to the ambient temperature. 

Tao

˄ć˅

Tao 

<22

ć

22

ć

< Tao <28

ć

Tao

ı

29

ć

Refrigeration/dehumidification 

(18K/24K) 

2nd

level /2nd

level

3rd

level /4th

level 5th

level /6th

level

Tao

˄ć˅

Tao 

<<10

ć

10

ć

< Tao <17

ć

Tao

ı

17

ć

Heating 

5th level /6th

level

3th level /5th

level 3rd

level  /2nd

level

After 3 minutes, the compressor is controled according to the ambient temperature and the frequency of the 

compressor. 

Refrigeration/dehumidification 

frequency

˄

Hz

˅

18K

˄

24K) 

<40 Hz 

40 Hz-60 Hz 

ı

60 Hz 

Tao

˄ć˅

İ

22 

2nd level 

3rd level 

5 th level(6 th) 

22-28

3rd level 

5 th level 

7 th level(6 th) 

ı

28

7 th level 

 Heating frequency

˄

Hz

˅

(18K/24K) 

<51 Hz 

51-70 Hz

ı

70 Hz 

Tao

˄ć˅

İ

10 

5nd level(3rd) 

6rd level 

7 th level 

10-17

3rd level(2nd) 

4 th level 

5 th level(6 th) 

ı

17

2nd level 

7.1.3 The control of the outdoor Electronic expansion valve (EEV) 

In cooling mode, the EEV opening range is 90~480 steps. The EEV opening is 90 steps when unit is 

off. 

In heating mode, the EEV opening range is 60~480 steps. The EEV opening is 60 steps when unit is 

off. 

After outdoor unit is off, the EEV opening keep the current on for 5 s, then open the EEV completely for 

2 minutes, then become 90 steps (cooling) or 60 steps (heating). 

Содержание 1U50S2SJ2FA-1












































































Отзывы: