background image

 

 

HC3 Owner’s Manual 

12/11/2013 

10 

Precautions  

Do 

1.

 

Comply with all state and local, building, plumbing, and electrical codes.  

2.

 

Install the appliance before the water heater.  

3.

 

Install the appliance after the pressure tank on well-water installations.  

4.

 

Install a pressure-reducing valve if the inlet pressure exceeds 70 psi (4.8 bar). 

5.

 

Examine the inlet line to ensure water will flow through it freely and that the inlet pipe is sized correctly. For 

well water with iron, the recommended minimum inlet pipe size is 3/4-inch I.D. and for municipal water the 

recommended minimum inlet pipe size is 1/2-inch I.D. 

6.

 

Install a gravity drain on the brine tank.  

7.

 

Secure the drain line on the appliance and at the drain outlet. See 

Installation Steps and Start-Up 

Procedures

. Install the drain line so that there is a 2-inch (5 cm) air gap between the drain line and the 

drain outlet. 

8.

 

Allow a minimum of 8 to 10 feet (2.4 to 3.0 m) of 3/4-inch pipe from the outlet of the appliance to the inlet of 

the water heater.  

Do Not 

1.

 

Do not install if checklist items are not satisfactory. See 

Checklist Before Installation

.  

2.

 

Do not install if the incoming or outlet piping water temperature exceeds 120°F (49°C). See 

Water 

Conditioner Specifications

.  

3.

 

Do not allow soldering torch heat to be transferred to valve components or plastic parts when using the 

optional copper adapters.  

4.

 

Do not overtighten the plastic fittings.  

5.

 

Do not plumb the appliance against a wall that would prohibit access to plumbing. See 

Installation Steps 

and Start-Up Procedures

.  

6.

 

Do not install the appliance backward. Follow the arrows on the inlet and outlet. 

7.

 

Do not plug the transformer into an outlet that is activated by an On/Off switch.  

8.

 

Do not connect the drain and the overflow (gravity drain) lines together.  

9.

 

Do not use to treat water that is microbiologically unsafe or of unknown quality without adequate 

disinfection before or after the appliance.  

10.

 

Do not allow your appliance or drain line to freeze. 

Note: 

A bacteriostasis claim does not mean that these devices will make microbiologically unsafe water safe to 

consume or use. 

Содержание Hydroclean HC3













































Отзывы: