background image

2-1

5 - DASH / AUT

O

SECTION 2 – SAFETY AND PRECAUTIONS

INTENDED USE

Most accidents occur as the result of failure to 

follow basic and fundamental safety rules and 
precautions. Recognizing potential safety 
hazards, following correct and safe operating 
procedures described in this manual, and 
complying with safety warnings located 
throughout the machine and attachment may 
reduce the risk of accidents.

There is no way to completely eliminate the 

potential for danger when operating agricultural 
equipment. Therefore, you must study this 
operator’s manual and understand how to operate 
the attachment controls for safe operation before 
using the attachment. Likewise, never let anyone 
operate the attachment without proper 
instruction.

Do not operate the attachment for anything 

other than its intended use. Hagie Manufacturing 
Company shall not be liable for any damage, 
injury, or death associated with improper use of 
the attachment.

Do not make any modifications such as, but 

not limited to, weldments, add-ons, adaptations, 
or changes from the original design of the 
attachment. Such modifications may become 
safety hazards to you and others and 

will void all 

warranties.

Replace missing, faded, or damaged safety 

signs. Refer to “Safety Decals” elsewhere in this 
section for correct sign and placement.

SAFETY PRECAUTIONS

General Safety

The hydraulic and electrical control systems 
are optimized for use with this attachment. 
Any modification to these systems may lead 
to unintended or uncontrolled motion. Do 
NOT install add-on control systems that are 
not approved by Hagie Manufacturing Com-
pany.

Some conditions cannot be completely safe-
guarded against without interfering with effi-
cient operation of the machine and/or 
reasonable accessibility. In these cases, 
decals have been installed to provide the 
operator with hazard information.
Do NOT remove decals for any reason. If a 
decal is damaged or missing, contact the 
Hagie Customer Support Department for 
replacement.

 

Wear Protective Clothing

Do not wear loose fitting clothing that could 
get caught in moving parts. Wear safety 
equipment that is appropriate for the job.

Do not store chemical-soaked clothing in the 
cab. Clean off as much mud and dirt from 
your shoes as you can before entering the 
cab.

NOTICE

This attachment is designed for and 
intended to be used for the application of 
nitrogen to field crops. Use in any other 
way or for any other purpose is 
considered misuse of this attachment.

Содержание 60' HsTB 24-Row
















































Отзывы: