manualshive.com logo in svg

Haes ESENTO ESEN-8MAR, Инструкция по установке, пусконаладке и эксплуатации, Страница: 32 / 68

Поделиться
Скачать
Haes ESENTO ESEN-8MAR Скачать руководство пользователя страница 32

Esento Marine 8-12 Installation, Commissioning & Operating Manual

Approved Document Ref: UI-ESEN12MAR-01 Issue 8.0

30

SETUP & PROGRAMMING

3

1

2

1

Zone Function Settings

There are 8 functional settings available for each zone. These are as follows:

Fire latching

Normally a zone latches a fire input signal. This setting allows the panel to clear automatically when a fire 

signal is removed. This is useful for interfacing purposes.

Short circuit as alarm (EN54!)

For Older non EN54 or BS5839 compliant systems. This allows a short circuit to generate a fire condition 

rather than a fault. 

Intrinsically safe operation

This option changes the zone alarm and short circuit thresholds to allow for an MTL 5561 type intrinsically 

safe barrier to be used in the circuit.

Silent mode

This setting provides a visual & audible alarm at the panel with no local sounder circuit operation.

Priority alarm (EN54!)

Normally a 220R call point will override delays or dependency alarms. This option allows turning off the 

priority alarm feature.

Detector removal (EN54!)

The  detector removal monitoring can be turned off. For use with older non compliant detectors.

Detector removal type

Schottky diode or Zener diode type detector bases for conventional zones (Does not apply to Twin wire 
circuits). The default operation is for shottky diode bases but can be changed for use with older Hochiki 

liveline bases or similar.

Содержание ESENTO ESEN-8MAR





































































Отзывы:

Нет отзывов