Haehne PAD2 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 14

Haehne PAD2 Скачать руководство пользователя страница 4

HAEHNE

Elektronische Messgeräte GmbH · Heinrich-Hertz-Str. 29 · D-40699 Erkrath Germany · Telefon 0211/9 25 91-0 · Fax 0211/9 25 91-20

http://www.haehne.de

Email: [email protected]

PAD2

Technical modifications reserved.

Page

4

3. Operating elements and functions

The portable force gauge has two operating modes:
- the measuring mode:
in this mode, the measurements are performed. This is the standard mode of the PAD2, which is always enabled
after switching on.
- the menu mode:
The most important data about the force gauge can be read out and configured.
In this mode, the force gauge is calibrated in the factory.

Button Name in the

measuring

mode

Function in the measuring

mode

(grey font)

Name in

the menu

Function in the menu

(light blue font)

ZERO
POSITIONING/
TARING

- Zero adjustment/taring and
- Clear peak values

up

-

scroll up in the menu

-

increase numeric values

PEAK

Toggle between displays:

-

of the actual measured value

-

of the max. value (= largest

value in positive force direction)

-

of the minimum value (= largest

absolute value in negative force
direction)

down

-

scroll down in the menu

-

decrease numeric values

ON/OFF

Switch on/off

escape

-

exit sub menu option during

entry without saving

-

exit menu, return to measuring

mode

MENU

Open the menu

enter

-

open selected menu option

-

confirm and save entry

«
...
2
3
4
5
6
...
»

Содержание PAD2















Отзывы:

Нет отзывов