HADEF 22/90 Скачать руководство пользователя страница 10

 

 

 

 

10 

 

 

5.52.653.00.01.06 

 

Arrow keys = drive left / right 

 

 

 

Illustration 4 

 

 

 

 

System start (optional) 

 

Illustration 5 

     

 

 

 

Push button functions (E) 

 

Relieved push button = stand still 

push button half pushed = slow speed 

push button pushed completely = fast speed 

 

 

Illustration 6 

 

 

 

Red Emergency-Stop button 

 

button pushed = stand still 

turn the button clockwise = free functions 

 

 

Illustration 7 

 

 

NOTICE!

 

Lockable Emergency-Stop buttons must first be opened with the key before unlocking! 

 

 

Operation 

 

The following, important points must be observed when operating the equipment: 

  Read the safety instructions. 

  Never load the devices beyond their working load limit. 

  When changing the motor turning direction, allow the motor to come to a standstill first. 

  The prescribed maintenance intervals must be adhered to. 

 

  Observe the duty cycle, i.e. intermittent operation S3-40% ED (as per VDE 0530) means that in a period 

of  10  minutes  the  motor  can  operate 

– no matter the height of the load – for 4 minutes.  It is therefore 

irrelevant whether the 4 minutes are continuous (i.e., in case of very high lifting heights) or are made in 
intervals. 

 

 

 

 

 

   

DANGER!

 

In particular, use is not permitted: 

    in  potentially  explosive  atmospheres,  unless  the  equipment  has  been  modified  for  this  purpose  and                    

this is shown on special type plates it carries for this purpose. 

    in reactor containments 

    for transporting persons  

    for holding lifted loads 

    for scenic use 

    when persons are under suspended loads 

 

 

Commissioning 

 

9.1 

General 

The operator of the unit is responsible for the entire system. 

According  to  the  Ordinance  on  Industrial  Safety  and  Health,  a  hazard  analysis  must  be  carried  out  by  the 
operator. 

Observe the respective national standards, regulations and directives of the responsible bodies at the place 
of operation.  

Содержание 22/90
















Отзывы: