Hach sension1 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 40

Hach sension1 Скачать руководство пользователя страница 5

5

CERTIFICATION

Hach Company certifies this instrument was tested thoroughly,
inspected, and found to meet its published specifications when it
was shipped from the factory.

The sens

ion

™

1 Portable pH Meter has been tested and is

certified as indicated to the following instrumentation standards:

EMI Immunity:

Per 89/336/EEC EMC: EN 61326:1998 (Electrical Equipment
for measurement, control, and laboratory use— EMC
requirements) Supporting test records by Hach Company,
certified compliance by Hach Company.

Standards include:
IEC 1000-4-2:1995 (EN 61000-4-2) Electro-Static Discharge
(Criteria B)

IEC 1000-4-3:1995 (EN 61000-4-3:1995) Radiated RF
Electro-Magnetic Field Immunity (Criteria B)

ENV 50204:1996 Radiated Electro-Magnetic Field from
Digital Telephones (Criteria B)

Radio Frequency Emissions:

Per 89/336/EEC EMC: EN 61326:1998 (Electrical Equipment
for measurement, control, and laboratory use— EMC
requirements) Class B emission limits. Supporting test records by
Criterion Technology O.A.T.S. (NVLAP #0369), certified
compliance by Hach Company.

Additional Emissions Standard/s include:

EN 55011 (CISPR 11) Emissions, Class B Limits

CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATION, IECS-003: Class A emission limits.
Supporting test records by Criterion Technology O.A.T.S.
(NVLAP #0369), certified compliance by Hach Company.

This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.

«
...
3
4
5
6
7
...
»

Содержание sension1









































Отзывы:

Нет отзывов