Hach sension1 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 40

Hach sension1 Скачать руководство пользователя страница 31

31

SECTION 4

TROUBLESHOOTING

4.1

Introduction

Correcting problem conditions with the sens

ion

™

electrochemical meters is limited to responding to the error
message displayed. Other problems must be handled by a Hach
technician at a service center. Refer to REPAIR SERVICE on page
38. Do not attempt to service the meter as there are no field-
serviceable parts. Opening the meter case will void the warranty.

4.2

Shorting Test

This test detects the meter offset.

1. Turn the meter on. Connect the shorting cap to the BNC

connector (see Figure 7). Unplug any electrodes from the
5-pin connector. Select the BNC connector from Setup 1.

2. Change the output to display in mV (press

pH/mV

to toggle

between pH and mV readings). After the meter has stabilized,
simultaneously press

CAL

and

ENTER

. The display should

show

0.0 mV

. If it does not, contact Hach Service.

Figure 7

Attaching Shorting Cap to The BNC Connector

«
...
29
30
31
32
33
...
»

Содержание sension1









































Отзывы:

Нет отзывов