Hach sension1 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 40

Hach sension1 Скачать руководство пользователя страница 25

25

SECTION 3

INSTRUMENT OPERATION

3.1

Setup Menu

The sens

ion

™

1 Portable pH meter has a setup menu that allows

the analyst to choose options for connector choice, display lock,
temperature units, automatic buffer recognition of pH 6.86 or 7.0,
and the display resolution.

To access the Setup menu, press the

SETUP

key. The arrow icons

will be displayed, indicating that additional options are available
within the menu. Press the up or down arrow key to scroll to the
desired option, then press

ENTER

. Table 3 describes these options.

3.1.1

Choosing the Probe Connector

This setup ensures the potential from the appropriate electrode is
detected by the meter. Connect only one electrode to the meter.

1. From the reading mode, press

SETUP

.

2. The

Setup

icon and the number

1

(flashing) will be displayed.

Change the connector choice by pressing

ENTER

; this toggles

the selection between

BNC

and

5 pin

.

3. When the desired option is selected, press

EXIT

to return to

the reading mode.

Table 3 Setup Options

Setup

Number

Option Description

1

Use BNC or 5-pin connector

2

Display lock (On or Off)

3

Temperature units (°C or °F)

4

Measurement resolution (0.0, 0.00, or 0.000)

5

Automatic buffer recognition (pH 7.00 or 6.86)

«
...
23
24
25
26
27
...
»

Содержание sension1









































Отзывы:

Нет отзывов