background image

Operating instructions 36001

 

 

Hot-pressing device 

PT-55 

 

 

 

Page 16 of

 

19 

Edition: 04/0401 

Subject to alterations 

9.3 Preparing 

devices 

9.3.1  Manual skiving tool AT-60 

The AT-60 is a preparing device for skiving of Habasit belts and tapes up to a width of 60 mm / 

2.4 in.

 and a 

thickness of 2 mm / 

0.08 in.

. The belt / tape is clamped and stuck on a steel plate. It is ground manually by 

means of a skiving disc. Adjustment is done with two different settings. 
The AT-60 is especially suitable for occasional preparation of single belts or spindle tapes on site in 
maintenance. 

 ill. (7) 

9.3.2  Skiving tool AT-200 

The AT-200 is a preparing device for skiving of Habasit belts and tapes up to a width of 200 mm and a 
thickness of 7 mm. The belt is clamped and stuck on a steel table. This table is adjustable in tilt in six steps; 
it is fed under a grinding drum on precise guides. For the drive of the unit there are two options: The device 
equipped with a high-torque power drill, or with a stub axle to be driven / motorized according to the desires 
of the customer. Feed of the table is by means of a hand wheel.  
The AT-200 is suitable for preparation of belts and tapes in small to medium series. 

 ill. (8) 

 

 

Illustration 7 

Illustration 8 

 

 

Содержание PT-55




















Отзывы: