H3C S6800 Series Скачать руководство пользователя страница 8

Страница: 8 / 56

# To display operating statistics on the monitor terminal, enter

at the prompt. (The output from

this command varies by software version.)

Save or display diagnostic information (Y=save, N=display)? [Y/N] :N

===============================================

===============display clock===============

23:49:53 UTC Tue 01/01/2016

=================================================

……

View diagnostic information:

Extract the file that contains diagnostic information.

<Sysname> tar extract archive-file diag_Sysname_20160101-000704.tar.gz

Extracting archive flash:/diag_Sysname_20160101-000704.tar.gz Done.

<Sysname> gunzip diag_Sysname_20160101-000704.gz

Decompressing file flash:/diag_Sysname_20160101-000704.gz.... Done.

View diagnostic information in the file.

<Sysname> more diag_Sysname_20160101-000704

===============================================

===============display clock===============

23:49:53 UTC Tue 01/01/2016

=================================================

---- More ----

Contacting technical support

If you cannot resolve a problem after using the troubleshooting procedures in this document, contact
H3C Support. When you contact an authorized H3C support representative, be prepared to provide
the following information:

•

Information described in "

General guidelines

•

Product serial numbers.

This information will help the support engineer assist you as quickly as possible.

The following is the contact information for H3C Support:

•

Telephone

number

—

400-810-0504.

•

E-mail

—

[email protected]

Содержание S6800 Series

























































Результаты поиска

Содержание S6800 Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S6800 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание S6800 Series

Отзывы:

Бренды по названию

Популярные бренды