H3C S6800 Series Скачать руководство пользователя страница 16

Страница: 16 / 56

Troubleshooting flowchart

Figure 5 Troubleshooting ACL application failure

Solution

Choose a solution depending on the module that uses the ACL.

ACL used in a QoS policy

To resolve the problem when the ACL is used in a QoS policy:

Verify that the QoS policy is configured correctly:

Use one of the following commands to check the QoS policy for configuration errors,
depending on the policy application destination:

Destination Command

Ethernet service instance

display qos policy l2vpn-ac

(This command is available in Release

24xx and Release 26xx.)

Interface

display qos

[

accounting

remarking

]

policy interface

(The

accounting

and

remarking

keywords are available in Release 26xx.)

VLAN

display qos vlan-policy

Global

display qos policy global

Control plane

display qos policy control-plane slot

slot-number

User profile

display

qos policy user-profile

If the QoS policy does not contain a class-behavior association, associate the traffic
behavior with the traffic class.

If the QoS policy contains a class-behavior association, execute the

display traffic

classifier user-defined

command and the

display traffic behavior user-defined

command to check for traffic class and behavior configuration errors, respectively.

Содержание S6800 Series

























































Результаты поиска

Содержание S6800 Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S6800 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание S6800 Series

Отзывы:

Бренды по названию

Популярные бренды