H3C S6800 Series Скачать руководство пользователя страница 20

Страница: 20 / 56

Troubleshooting flowchart

Figure 6 Troubleshooting IRF fabric setup failure

Does the number

of members exceed the upper

limit?

Is member ID unique

for each member?

You cannot add devices

to the IRF fabric or

complete IRF merge

Assign a unique

member ID to each

member device

Do member devices

use the same software

version?

Upgrade software to

the same version

Contact the support

IRF setup failure

Yes

Resolved?

Yes

Resolved?

Yes

End

Are IRF port

bindings or physical IRF

connections correct?

Modify IRF port

bindings or reconnect

IRF physical interfaces

Resolved?

Yes

Bring up the IRF links

or activate IRF port

configuration

Resolved?

Yes

Are IRF links up?

Do physical IRF

links meet the rate

requirements?

Replace with correct

transceiver modules or

cables

Resolved?

Yes

Are specific settings

same across member

devices?

Modify the settings to

be the same

Resolved?

Yes

Can member

devices join the same IRF

fabric?

Replace with devices

that can join the same

IRF fabric

Yes

Resolved?

Yes

Содержание S6800 Series

























































Результаты поиска

Содержание S6800 Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S6800 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание S6800 Series

Отзывы:

Бренды по названию

Популярные бренды