H3C S6520X-SI Series Скачать руководство пользователя страница 83

Страница: 83 / 90

Item Specification

Interface attributes

1/2.5/5 Gbps, full duplex, MDI/MDI-X, auto-sensing

Max transmission distance

5 Gbps:

•

Category-5e UTP

—55 m (180.45 ft)

•

Category-5e STP

—100 m (328.09 ft)

•

Category-6 twisted pair

—100 m (328.09 ft)

•

Category-6e twisted pair

—100 m (328.09 ft)

2.5 Gbps:

Category-5e and above twisted pair

—100 m (328.09 ft)

Transmission medium

Category-5e (or above) twisted pair cable

Standards

IEEE 802.3ab, 802.3an

10G/5G/2.5G/1000BASE-T autosensing Ethernet port

The S6520X-10XT-SI and S6520X-16XT-SI switches and the LSWM2XMGT8P interface module
provide 10G/5G/2.5G/1000 BASE-T autosensing Ethernet ports.

Table 33 10G/5G/2.5G/1000BASE-T autosensing Ethernet port specifications

Item Specification

Connector type

RJ-45

Interface attributes

1/2.5/5/10 Gbps, full duplex, MDI/MDI-X, auto-sensing

Max transmission distance

10 Gbps:

•

Category-6 UTP

—55 m (180.45 ft)

•

Category-6 STP

—100 m (328.09 ft)

•

Category-6e twisted pair

—100 m (328.09 ft)

5 Gbps:

•

Category-5e UTP

—55 m (180.45 ft)

•

Category-5e STP

—100 m (328.09 ft)

•

Category-6 twisted pair

—100 m (328.09 ft)

•

Category-6e twisted pair

—100 m (328.09 ft)

2.5 Gbps:

Category-5e and above twisted pair

—100 m (328.09 ft)

Transmission medium

Category-5e (or above) twisted pair cable

Standards

IEEE 802.3ab, 802.3an

10G/5G/2.5G/1000/100BASE-T autosensing Ethernet port

The S6520X-26XC-UPWR-SI and S6520X-54XC-UPWR-SI switches provide
10G/5G/2.5G/1000/100 BASE-T autosensing Ethernet ports.

Table 34 10G/5G/2.5G/1000/100 BASE-T autosensing Ethernet port specifications

Item Specification

Connector type

RJ-45

Interface attributes

•

100 Mbps, full/half duplex, MDI/MDI-X, auto-sensing

Содержание S6520X-SI Series



























































































Результаты поиска

Содержание S6520X-SI Series

Отзывы:

H3C S6520X-SI Series, Руководство по установке, Страница: 83 / 90

Результаты поиска

Содержание S6520X-SI Series

Отзывы: