H3C S6520X-SI Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 90

H3C S6520X-SI Series Скачать руководство пользователя страница 81

73

Figure 73 40G QSFP+ to SFP+ cable

(1) QSFP+ module

(2) QSFP+ side pull tab

(3) SFP+ side pull tab

(4) SFP+ module

IMPORTANT:

You can use a QSFP-40G-SR4-MM850 or QSFP-40G-CSR4-MM850 transceiver module to
connect a QSFP+ port to four SFP+ ports. The QSFP+ transceiver module and SFP+ transceiver
modules to be connected must be the same in specifications, including central wavelength and fiber
type.

NOTE:

•

As a best practice, use H3C QSFP+ transceiver modules, QSFP+ cables, or QSFP+ to SFP+

cables for the QSFP+ ports on the switch. The H3C QSFP+ transceiver modules, QSFP+ cables,
and QSFP+ to SFP+ cables available for the QSFP+ ports are subject to change over time. For
the most recent list of QSFP+ transceiver modules, QSFP+ cables, and QSFP+ to SFP+ cables
available for the QSFP+ ports, contact H3C Support or marketing staff.

•

For more information about H3C QSFP+ transceiver modules, QSFP+ cables, and QSFP+ to

SFP+ cables, see

H3C Transceiver Modules User Guide

.

10/100/1000BASE-T autosensing Ethernet port

An LSPM4G4T6P interface module provides 10/100/1000BASE-T autosensing Ethernet ports.

Table 29 10/100/1000BASE-T autosensing Ethernet port specifications

Item Specification

Connector type

RJ-45

Interface attributes

•

10/100 Mbps, full/half duplex, MDI/MDI-X, auto-sensing

•

1 Gbps, full duplex, MDI/MDI-X, auto-sensing

Max transmission distance

100 m (328.08 ft)

Transmission medium

Category-5 (or above) twisted pair cable

Standards

IEEE 802.3i, 802.3u, 802.3ab

3

4

1

2

«
...
79
80
81
82
83
...
»

Содержание S6520X-SI Series



























































































Отзывы:

Нет отзывов