H3C S6520X-SI Series Скачать руководство пользователя страница 68

Страница: 68 / 90

Appendix B FRUs and compatibility
matrixes

The S6520X-SI switches (except the S6520X-10XT-SI and S6520X-16XT-SI) use modular design
and support FRUs.

Table 13

and

Table 14

describe the FRUs available for the switches and the

compatibility between the FRUs and the switches.

The S6520X-10XT-SI and S6520X-16XT-SI switches use one built-in power module and two built-in
fan trays and do not support FRUs.

Table 13 FRUs and compatibility matrixes (1)

FRUs

S6520X-16ST-SI/S6
520X-24ST-SI

S6520X-18C-SI/S65
20X-18C-SI

S6520X-26MC-SI

Removable power modules

PSR75-12A Supported

Supported

Not

supported

PSR150-A1 Supported

Supported

PSR150-D1 Supported

Supported

Expansion cards

LSWM2QP2P Not

supported

Supported

LSWM4SP8PM Not

supported

Supported

LSWM2SP8P Not

supported

Supported

LSWM2SP2PM Not

supported

Supported

LSWM2XGT2PM

Not supported

Supported

LSPM4G4T6P Not

supported

Supported

LSPM6FWD Not

supported

Supported

LSWM2MGT8P Not

supported

Supported

LSWM2XMGT8P

Not supported

Supported

LSWM2ZSP2P Not

supported

Supported

LSWM2SP2PB Not

supported

Supported

LSWM2SP4PB Not

supported

Supported

Table 14 FRUs and compatibility matrixes (2)

FRUs

S6520X-26MC-UPW
R-SI

S6520X-26XC-UPWR-SI

S6520X-54XC-UPWR-SI

Removable power modules

PSR360-56A Supported

Supported

PSR720-56A Supported

Supported

PSR1110-56A Supported

Supported

PSR560-56D Supported

Supported

Содержание S6520X-SI Series



























































































Результаты поиска

Содержание S6520X-SI Series

Отзывы:

H3C S6520X-SI Series, Руководство по установке, Страница: 68 / 90

Результаты поиска

Содержание S6520X-SI Series

Отзывы: