background image

 

B-3 

Japan regulatory compliance 

VCCI  

H3C S5810-50S complies with the requirements of VCCI Class A Information Technology Equipment 

(ITE).  

Warning: 

If this equipment is used in a domestic environment, radio disturbance may arise. When such 

trouble occurs, the user may be required to take corrective actions. 

CISPR 22 compliance 

H3C S5810-50S complies with the requirements of CISPR 22 for Class A Information Technology 

Equipment (ITE). 

Warning:

 If this equipment is used in a domestic environment, radio disturbance may arise. When such 

trouble occurs, the user may be required to take corrective actions. 

产品符合

CLASS A 

的声明

 

 

此为

A

级产品,在生活环境中,该产品可能会造成无线电干扰。在这种情况下,可能需要用户对其干扰

采取切实可行的措施。

 

 

Safety Information Sicherheits informationen

安全信息

 

Overview Überblick 

概述

 

This section introduces part of the safety precautions that should be followed during the installation and 

maintenance of the equipment. And for the safety statements and warnings, there followed the 

translations of both German and Chinese to comply with the national requirements.  

Dieser Abschnitt macht Sie mit den Sicherheitsvorschriften vertraut, die Sie bei der Installation und 

Instandhaltung der Ausrüstung beachten müssen. 

本章节介绍了在安装、日常维护本系列设备时,必须遵循的安全预防规范。

 

Содержание S5810 Series


























































Отзывы: