H3C S5810 Series Скачать руководство пользователя

Страница: 46 / 57

A-2

Make sure that the arrester is well grounded before using the lightning arrester for power.

After inserting AC power cord plug of switch into the socket of lightning arrester, if the green LED is

on and the red LED does not alarm, it means that the lightning arrester of power is running and the

function of lightning protection has taken effect.

Pay adequate attention if the red LED is on. You should correctly locate the problem, whether it is

caused because the ground wire of the arrester is not well grounded or because the live and zero

wires are connected in reverse direction. You may check that in the following way. When the red

LED is on, use a multimeter to examine polarity at the power socket of the arrester. If it is same to

that of the power socket in the equipment room, it means that arrester is not well grounded. If it is

adverse to that of the power socket in the equipment room, it means that the power socket of the

arrester is set to the reverse polarity. In this case, you should open the power socket of arrester to

correct polarity. After that, if the red LED still alarms, it means that the arrester is not well grounded

yet.

Installation of Lightning Arrester for Network Port

Lightning arrester for network port is specially designed for the Ethernet port of 10/100/1000M electrical

interface (RJ-45 connector is adopted in this case).

Lightning arrester for network port will not be provided along with the switch, and you should purchase

it by yourself if needed.

If an outdoor network cable should be led to the switch, please serially connect the lightning arrester for

network port before you plug this cable into the interface on the switch, in case of the possibility that the

switch may be damaged due to lightning strike.

Required tools

Phillips screwdriver or Flat-blade screwdriver

Multimeter

Tilted wire cutter

Installation procedure

Step 1: Tear the protection paper at one side of the double faced adhesive tape apart from the tape, and

stick the tape on the surface of the arrester. Tear the protection paper at another side apart from the

tape, and stick the arrester onto the chassis of the switch. The arrester should be attached on the

chassis as close to the grounding screw as possible.

Содержание S5810 Series


























































Результаты поиска

Содержание S5810 Series

Отзывы:

Похожие инструкции для S5810 Series

Бренды по названию

Популярные бренды

H3C S5810 Series, Быстрый старт

Результаты поиска

Содержание S5810 Series

Отзывы:

Похожие инструкции для S5810 Series

Бренды по названию

Популярные бренды