H3C S5500-SI Series Скачать руководство пользователя

Страница: 30 / 130

3-5

Tasks

Remarks

Basic Configuration Tasks

Required

These configurations are the foundation for other configuration tasks.

Configuring CC on MEPs

Required

Configuring the MEPs to send CCMs to manage link connectivity

Configuring LB on MEPs

Optional

Checking link state by testing link connectivity

Configuring LT on MEPs

Optional

Tracing link fault and finding the path between the source MEP and target

MEP

A port blocked by STP cannot receive, send, or respond to CFD messages, however, if the port is

configured as an outward-facing MEP, it can still receive and send CCM messages even if it is

blocked by STP.

Only Ethernet ports support CFD.

Basic Configuration Tasks

Basic configuration tasks include:

Configuring Service Instance

Configuring MEP

Configuring MIP Generation Rules

Based on the network design, you should configure MEPs or the rules for generating MIPs on each

device. However, before doing this you must first configure the service instance.

Configuring Service Instance

A service instance is indicated by an integer to represent an MA in an MD. The MD and MA define the

level and VLAN attribute of the messages handled by the MPs in a service instance.

Follow these steps to configure a service instance:

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды