H3C S5500-SI Series Скачать руководство пользователя

Страница: 33 / 130

3-8

Any of the following actions or cases can cause MIPs to be created or deleted after you have

configured the

cfd mip-rule

command:

Enabling CFD (use the

cfd enable

command)

Creating or deleting the MEPs on a port

Changes occur to the VLAN attribute of a port

The rule specified in the

cfd mip-rule

command changes

Configuring CC on MEPs

After the CC function is configured, MEPs can send CCMs mutually to check the connectivity between

them.

Configuration Prerequisites

Before configuring this function, you should first complete the MEP configuration.

Configuring Procedure

After the CC function is configured, MEPs can send CCM frames to one another to check the

connectivity between them.

You must configure CC before configuring other CFD functions.

Follow these steps to configure CC on a MEP:

To do...

Use the command...

Remarks

Enter system view

system-view

—

Configure the interval field value in

the CCM messages sent by MEPs

cfd cc interval

interval-field-value

service-instance instance-id

Optional

By default, the interval filed value

is 4.

Enter Ethernet port view

interface interface-type

interface-number

—

Enable CCM sending on a MEP

cfd cc service-instance

instance-id mep mep-id enable

Required

Disabled by default

The relationship between the interval field value in the CCM messages, the interval between CCM

messages and the timeout time of the remote MEP is illustrated in

Table 3-1

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды