manualshive.com logo in svg

H3C S5500-EI series, Руководство по эксплуатации, Страница: 505 / 1529

Поделиться
Скачать
H3C S5500-EI series Скачать руководство пользователя страница 505

Operation Manual – IPv6 Routing 
H3C S5500-EI Series Ethernet Switches 

Chapter 1  IPv6 Static Routing Configuration

 

1-1 

Chapter 1  IPv6 Static Routing Configuration 

 

 

  Note:  

The term “router” in this document refers to a Layer 3 switch running routing protocols. 

 

1.1  Introduction to IPv6 Static Routing 

Static routes are special routes that are manually configured by network administrators. 

They work well in simple networks. Configuring and using them properly can improve 

the performance of networks and guarantee enough bandwidth for important 

applications. 

However, static routes also have shortcomings: any topology changes could result in 

unavailable routes, requiring the network administrator to manually configure and 

modify the static routes. 

1.1.1  Features of IPv6 Static Routes 

Similar to IPv4 static routes, IPv6 static routes work well in simple IPv6 network 

environments. 

Their major difference lies in the destination and next hop addresses. IPv6 static routes 

use IPv6 addresses whereas IPv4 static routes use IPv4 addresses.  

1.1.2  Default IPv6 Route 

The IPv6 static route that has the destination address configured as 

::/0

 (indicating a 

prefix length of 0) is the default IPv6 route. If the destination address of an IPv6 packet 

does not match any entry in the routing table, this default route will be used to forward 

the packet. 

1.2  Configuring an IPv6 Static Route 

In small IPv6 networks, IPv6 static routes can be used to forward packets. In 

comparison to dynamic routes, it helps to save network bandwidth. 

1.2.1  Configuration prerequisites 

z

 

Enabling IPv6 packet forwarding 

z

 

Ensuring that the neighboring nodes are IPv6 reachable 

Содержание S5500-EI series


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов