H3C H3C S5100-SI Скачать руководство пользователя страница 93

Страница: 93 / 104

Installation Manual
H3C S5100-SI/EI Series Ethernet Switches

Chapter 5 Boot ROM and Host Software Loading

5-9

2. Set FTP protocol parameter

3. Set XMODEM protocol parameter

0. Return to boot menu

Enter your choice(0-3):

Step 4: Select 1 to download the Boot ROM software using TFTP. Then set the

following TFTP-related parameters as required:

Load File name :S5100.btm

Switch IP address :1.1.1.2

Server IP address :1.1.1.1

Step 5: Press <Enter>. The system displays the following information:

Are you sure to update your bootrom?Yes or No(Y/N)

Step 6: Enter Y to start file downloading or N to return to the Boot ROM update menu. If

you enter Y, the system begins to download and update the Boot ROM software. Upon

completion, the system displays the following information:

Loading........................................done

Bootrom updating..........done!

III. Loading host software

Step 1: Select 1 in Boot Menu. The system displays the following information:

1. Set TFTP protocol parameter

2. Set FTP protocol parameter

3. Set XMODEM protocol parameter

0. Return to boot menu

Enter your choice(0-3):1

To load the host software through TFTP, select 1.

The subsequent steps are the same as those for loading the Boot ROM software,

except that the system gives the prompt for host software loading instead of Boot ROM

5.2.4 Loading Software Using FTP Through Ethernet Port

I. Introduction to FTP

File Transfer Protocol (FTP) is an application-layer protocol in the TCP/IP protocol suite.

It is used for transferring files between server and client, and is widely used in IP

networks.

You can use FTP to load software onto the switch through an Ethernet port. In this case,

the switch can act as an FTP server or an FTP client. In the following example, the

switch acts as an FTP client.

Содержание H3C S5100-SI









































































































Результаты поиска

Содержание H3C S5100-SI

Отзывы:

Бренды по названию

Популярные бренды

H3C H3C S5100-SI, Руководство по установке

Результаты поиска

Содержание H3C S5100-SI

Отзывы:

Бренды по названию

Популярные бренды