H3C H3C S5100-SI Скачать руководство пользователя страница 32

Страница: 32 / 104

Installation Manual
H3C S5100-SI/EI Series Ethernet Switches

Chapter 1 Product Overview

1-25

Table 1-5

Description of the mode LED

LED

Mark

Status

Description

OFF Invalid

Green, ON

The port LED is indicating rate mode.

Yellow, ON

The port LED is indicating duplex mode.

Mode LED

Mode

Green,
blinking (1 Hz)

The port LED is indicating PoE mode.

1.4.4 Gigabit Autosensing Ethernet Port Status LEDs

The Gigabit autosensing Ethernet port status LEDs are yellow-green indicator.

Table 1-6

Description of Gigabit autosensing Ethernet port status LEDs

Port mode

LED status

Description

The port is connected at 1,000
Mbps.

Green

Blinking (30 ms
per packet)

The port is receiving or sending
data at 1,000 Mbps.

The port is connected at 10/100
Mbps.

Blinking (30 ms
per packet)

The port is receiving or sending
data at 10/100 Mbps.

Yellow

Blinking (3 Hz)

Port POST has failed.

Rate mode

OFF

The port is not connected.

The port is working in full duplex
mode.

Green

Blinking (30 ms
per packet)

The port is receiving or sending
data in full duplex mode.

The port is working in half duplex
mode.

Blinking (30 ms
per packet)

The port is receiving or sending
data in half duplex mode.

Yellow

Blinking (3 Hz)

Port POST has failed.

Duplex
mode

OFF

The port is not connected.

Содержание H3C S5100-SI









































































































Результаты поиска

Содержание H3C S5100-SI

Отзывы:

Бренды по названию

Популярные бренды

H3C H3C S5100-SI, Руководство по установке

Результаты поиска

Содержание H3C S5100-SI

Отзывы:

Бренды по названию

Популярные бренды