H.C Duke & Son Freedom 360 Degrees 927CMT, Руководство оператора с иллюстрированным перечнем запчастей

Страница: 160 / 160

A B
Left Right
Side Side
1. Instruct the owner/operator on proper
cleaning and sanitizing as outlined
in the Operator's Manual. .......................
†
2. Drain sanitizer from the freezer. .............
† †
3. Pour at least 2-1/2 gallons of mix into
each mix container. ................................
† †
4. Open dispensing spigot and air
relief/bleed plug. Turn MTS switch to
"ON". Leave spigot open until pure mix
comes out of dispensing head then close
spigot. Close air relief/bleed plug when
mix is coming out of the air relief/bleed plug
opening in the bottom of the head. .......
† †
A B
Left Right
Side Side
5. Allow MTS to run until it shuts off on
pressure. ...................................................
† †
6. Turn selector switch to "AUTO" ................
† †
7. Allow refrigeration to cycle, record cycle
times once down to dispensing temperature
(approxiamtely 15-20 minutes).
Length of on time and off time ........... ON ______
______
OFF ______ ______
8. Completely review all portions of freezer
start-up. ....................................................
†
9. Explain overrun, how to check, calculate
and change. ..............................................
†
10. Explain and have operator/owner sign
warranty card. ...........................................
†
Installation Adjustments
A B
Left Side Right Side
1. Check refrigerant charge - sight glass. ............................................................................ First check
† †
Second check
† †
2. Check, set and record head pressure. .......................................................................... First check _____psig _____psig
Second check _____psig _____psig
3. Check, set and record cylinder expansion valve pressure. ........................................... First check _____psig _____psig
Note: Cabinet refrigeration must be turned off while checking. (Some models) Second check _____psig _____psig
4. Check and record cabinet suction pressure. ................................................................ First check _____psig
NOTE: cylinder refrigeration must be turned off while checking. (Some models) Second check _____psig
5. On freezers equipped with adjustable timers. Check and record settings. ................ Beater Delay ________ _______
Compressor Delay ________ _______
Beater Recycle (High Capacity Models) ________ _______
Dispense (High Capacity Models) ________ _______
6. What product is being used. ................................................................................................. A Side __________________
B Side __________________
7. Set cylinder thermostat to maintain desired temperature.
Record settings. ............................................................................................................. First check ___/___ ___/___
Second check ___/___ ___/___
8. Check and record actual product dispensing temperature. .......................................... First check _____°F _____°F
Second check _____°F _____°F
Beater Delay _____ _____
Compressor Delay _____ _____
9. Check and record air meter size. .......................................................................................... Check _____ _____
10. Make sure freezer cycles off with all microswitch spigot rods removed. ........................................
† †
11. Make sure spigot rod starts the appropriate side and the freezer cycles off after activation in
the amount of time set on the dispense timer. ................................................................................
†
12. Reinstall all panels and panel screws. .............................................................................................
†
NOTE: Wait approximately two (2) hours and recheck and record all installation adjustments again.
Verify freezer is properly set. This check should be recorded in the second check column.
Remarks: __________________________________________________________________________________________________
Installation Checked and Inspected By:
Print Name: ______________________________ Signature: __________________________________ Date: _________________
Check one:
†
Distributor
†
Service Agency
Operator/Owner Training Completed By:
Print Name: ______________________________ Signature: __________________________________ Date: _________________
Check one:
†
Distributor
†
Service Agency
I hereby certify this equipment has been inspected and is in satisfactory operating condition. It has been demonstrated for proper start-up and
operating procedures. The potential dangers which could occur if the freezer is not operated properly have been explained to me and I have
read and understand the warranty attached to the Warranty Registration Card.
Signature required.
Print Name: ______________________________ Purchaser: _________________________________ Date: _________________
Print Name: _______________________________ Operator: _________________________________ Date: _________________
IMPORTANT: Installer and owner retain copy for reference.
IMPORTANT: MAIL WARRANTY REGISTRATION CARD TO VALIDATE AND START WARRANTY PERIOD.
INS-805 Rev. 01, 2/08
Owner/Operator Training
Machine Start-up
Page 2