manualshive.com logo in svg

Guilin Woodpecker Medical Instrument Fi-G, Инструкция по эксплуатации, Страница: 25 / 31

Поделиться
Скачать
Guilin Woodpecker Medical Instrument Fi-G Скачать руководство пользователя страница 25

23

Charging 

failure after 

connecting to 

power supply.

1. The power supply is not 

correctly connected;

2. The power supply is 

damaged, or the specification 

doesn’t match.

3. There are impurities on the 

contact thimble of charging 

base.

1. Unplug and reconnect. 

2. Replace the battery.

3. Wipe the thimble 

with alcohol, dry it, and 

reconnect.

The service 

time after each 

charging is 

shortened.

The battery capacity 

becomes smaller.

Send to the repair center.

ERROR code 

appears on 

display screen.

The heating chamber is 

damaged.

1. Send to the repair 

center.

2. Contact local distributor 

or manufacturer.

If the problem still cannot be solved, please contact your local dealer 

or our company.

1. When the pushing ram is in the Hot Melting and Filling Instrument, 

please do not push or pull the pushing ram vigorously. When the gutta-

percha is heated up to the preset temperature, the pushing ram should be 

pushed by pulling the trigger for multiple times. If the pushing ram does 

not move, try to push it manually with a slight force, and try to pull the 

trigger. 

2. Please refer to the recommended temperature to set the preset 

temperature.

3. To remove all remaining material, please first remove the needle, 

and then pull the trigger to squeeze out all the residual material in the 

heating chambers. Be careful not to touch the head of the Hot Melting 

and Filling Instrument to avoid scalding. Power off, cool it down slightly, 

and push the pushing ram down.

10 After-sales service

Since the date of sales, if the device cannot work normally for quality 

problem, our company will be responsible for the repair of device during 

the warranty period. Please refer to the Warranty Card for warranty 
period and warranty scope.

Содержание Fi-G
































Отзывы:

Нет отзывов