Guilin Woodpecker Medical Instrument Fi-G Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 31

Guilin Woodpecker Medical Instrument Fi-G Скачать руководство пользователя страница 2

Contents

Introduction -------------------------------------------------------1
1 Product introduction -------------------------------------------1
2 Standard icons --------------------------------------------------9
3 Contraindications -------------------------------------------- 10
4 Installation and disassembly method of accessories ---- 10
5 Operation method --------------------------------------------11
6 Charging instruction ----------------------------------------- 13
7 Safety precautions ------------------------------------------- 14
8 Cleaning, Disinfection, Sterilization and Maintenance 14
9 Troubleshooting ---------------------------------------------- 22
10 After-sales service ------------------------------------------ 23
11 Environment protection ------------------------------------ 24
12 EMC-Declaration of comformity ------------------------ 24
13 Statement ---------------------------------------------------- 28

«
1
2
3
4
...
»

Содержание Fi-G
































Отзывы:

Нет отзывов