Guilin Woodpecker Medical Instrument Fi-G Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 31

Guilin Woodpecker Medical Instrument Fi-G Скачать руководство пользователя страница 13

11

screwdriver, then remove the battery cover, next remove the old battery,

replace it with a new one, and finally cover the battery cover and tighten

the screws.

Warning:

Improper replacement of lithium batteries may result in unacceptable

risks,so replacement of lithium batteries requires trained personnel.

4.5 Installation and disassembly of pushing ram

When pulling out the pushing ram, the limit switch must be kept

pressed.

The pushing ram can only be plugged in or unplugged from tail part of

the Hot Melting and Filling Instrument.

5 Operation method

Note:

During use, please do not contact the heating part of the Hot

Melting and Filling Instrument. Before use, remember to install the

Thermal Protector Cap to prevent users or patients from scalding.

1. Choose Gutta Percha Injecting Needle

Choose suitable Gutta Percha Injecting Needle (20ga, 23ga or 25ga)

according to the situation of patient. And tighten the Gutta Percha

Injecting Needle and handpiece (Note: not too tight). When using, the

Gutta Percha Injecting Needle can rotate to suitable angle within the

range of 360°in clockwise direction and counterclockwise direction. And

you can also use wrench to pre-bend the needle and adjust it to a better

operation angle as per your needs.

Warning:

When install the Gutta Percha Injecting Needle, please be sure that

the device is off and the head part of the device is cooling down. (About

5 minutes after shutdown of the Hot Melting and Filling Instrument, the

head part of it can cool down to the temperature that allows people to

touch.)

«
...
11
12
13
14
15
...
»

Содержание Fi-G
































Отзывы:

Нет отзывов