background image

Page 10 of 13 

 

14.  Disconnect the positive (red)(+) clamp and then the negative(black) (

–) clamp from the battery of 

the vehicle.  

15.  Store the clamps separately after use. 

16.  Recharge the booster pack immediately after use. 

 

WARNING

 

 

Allow the power pack to cool down for at least 3 minutes after each boost.

 

  F

ollow these instructions carefully for boosting your vehicle. The instructions may be different 

from those mentioned for other boosting products or cables.

 

 

If boosting a boat engine, purge the engine compartment and vent all fumes before boosting.

 

  Do 

not crank the engine for more than 5 seconds. The power pack feature is designed only for 

short term operation. Failure to comply may cause damage to the device.

 

 

CAUTION

 

EQUIPMENT DAMAGE 

 

Use only the supplied boost cables to boost a vehicle or boat engine that has a 12V starting 
battery. 

 

Ensure that the power pack is placed away from the moving parts of the engine and power pack 
power ON/OFF switch is in OFF position. 

 

Make sure the cable clamps are connected correctly to the battery terminals. A reversed polarity 
connection (positive to negative) may cause a spark and damage the equipment. If the cable 
clamps are connected in reverse, the reverse polarity LED indicator glows red and the audible 
alarm will sound. 

 

If the glow of the correct connection indicator is green without the sound alarm, the connections 
are proper. 

 

Ensure that the power pack and the cables are away from the belts, fans or any other moving part 
of the engine. 

 

Using the Air Compressor 

WARNING

 

 

The compressor is designed for short term operation only. Operating the compressor over an 
extended period of time will cause the compressor unit to overheat, which could lead to fire. 
Allow the compressor to cool down for 10 minutes after each 10 minutes of continuous operation. 

 

Do not leave the compressor unattended while in operation 

 

 Keep out of children. 

 

If the power pack shuts off due to an over-temperature condition, turn OFF the air compressor 
switch and allow the compressor to cool down for 15 minutes before re-starting.  

 

The power pack cannot be used to inflate large capacity inflatables such as float tubes, large air 
mattresses, transport truck tires, and inflatable boats. These types of products require extended 
inflating time which may damage the compressor. 

Содержание 699784














Отзывы: