background image

 

10 

Troubleshooting 

 

Under normal use, your Guest Model 501 Beamer Remote Controlled Spotlight will 
provide you with many years of reliable service.  If your unit should become damaged 
by a severe impact, we recommend that you contact the Guest Company Service 
Department. See page 12 for contact information. 
 

 

If an operational problem occurs: 

 

1.

 

Confirm  that  all  fuses  are  intact

.    If  a  fuse 

has

  blown,  do  not  replace  the  fuse 

until the cause of the problem has been located and corrected.  NEVER replace a 
blown fuse with a higher value fuse.  

 

2.

 

Most problems are caused by poor wiring connections

.  Confirm that all wiring  

     

connections are accurate and well made. The connections of the wires are 

     important and should be soldered and then taped, or connected using  
     weatherproof phone splices.  Be sure that the spotlight is connected to a DC power  
     source capable of supplying 

at least

 12 volts at 10 amps even while other    

     equipment is operating. 
 

    3.  If the spotlight does not move or light: 

a.

 

Observe the wireless transmitter.  The Red light on the transmitter should turn 
on whenever a button is pressed.  If it does not, first check the internal battery 
polarity, if correct then replace the transmitter.   

b.

 

Disconnect the 12 Volt DC power from the spotlight. Reconnect the 12 Volt DC 
power  to  the  spotlight.  Press  the  green  On/Off  button  2-3  times  within  5 
seconds of applying power to the light. 

c.

 

Remove the 4 bolts that fasten the spotlight onto the mounting surface and  

     gently lift the unit until you can see inside its base.  Avoid cutting any wires. 
     Gently inspect the wiring inside the base for broken connections.  Examine the 

               circuit board for loosened plug connectors, blackened components or 
               corrosion.  Replace the circuit board if it appears damaged.  If there are no  
               loose wires or signs of water penetration, re-install the spotlight and then 
               replace the wireless transmitter.  If there are signs of damage, 
               contact The Guest Company Service Department for advice.   
               See page 12 for contact information. 
               Have available information on how and where the spotlight was installed. 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Содержание 729825













Отзывы: