GUDNORD+ 39062269974, Инструкция по эксплуатации

Страница: 11 / 84

GB | 11
When re-commissioning after a long period of storage
1. Change the engine oil.
2. Fill with fresh petrol before starting the motor after the stor-
age period.
If the engine is not used for more than one month, changes to the
petrol quality may result in difficulties starting the engine or in
other issues. To prevent this, loosen the carburettor’s drain screw
and allow the petrol to run out. Also open the fuel valve so that the
petrol drains from the tank.
13. Maintenance
Attention!
Always shut the engine down and remove the spark plug connector
before carrying out any maintenance work.
Changing the oil (fig. 8)
Change the engine oil after 25 operating hours, then after 50
hours or every three months.
Drain the engine oil when the engine is hot.
1. Warm the engine up.
2. Switch the engine off.
3. Place a container that is large enough to collect the used oil
under the oil drain screw (c).
4. To drain the oil, remove the screw-on oil cap (10) and the
oil drain screw (c).
5. Drain the oil
6. Re-attach the oil drain screw (c) with a sealing washer and
tighten.
7. Pour the recommended engine oil into the oil filler hole.
Note! Tightly screw the oil filler cap with dipstick (10).
Capacity: approximately 0.6 litres Dispose of the drained oil prop-
erly at a local used oil collection point. Dumping used oil in the soil
or mixing it with waste is prohibited.
Check the spark plug (fig. 10)
Switch off the engine and allow it to cool. Caution! Danger of
burning Clean or replace spark plug as required:
1. Remove the spark plug connector (f) and clean any dirt from
the spark plug area.
2. Unscrew the spark plug and check it.
3. If there is any damage, e.g. cracks or chips, replace the
spark plug.
4. Clean the spark plug electrodes with a wire brush.
5. Check and set the electrode gap.
6. Screw the spark plug in and tighten with the spark plug
spanner.
7. Place the spark plug connector (f) on the spark plug.
10. Cleaning
Attention!
Always shut the engine down and remove the spark plug connector
before carrying out any cleaning work.
We recommend that you clean the device directly after every use.
Clean the device at regular intervals using a damp cloth and a little
soft soap.
Do not use any cleaning products or solvents; they could
attack the plastic parts of the device. Make sure that no water can
penetrate the device interior.
11. Transport
Transport
1. Allow the engine to cool before transporting.
2. Before transporting the power unit, switch the engine switch
(9) to the OFF position and turn the fuel valve (4) to the
OFF position
3. Keep the power unit level so that no petrol is spilled. Petrol
vapour or spilled petrol may ignite.
4. Ensure that the power unit does not fall and do not subject it
to any blows during transport.
5. For short transport, transport the generator using the trans-
port wheels (15) and the transport handle (8).
12. Storage
Store the device and its accessories in a dark, dry and frost-free
place that is inaccessible to children. The optimum storage temper-
ature lies between 5 and 30 ˚C. Store the power tool in its original
packaging. Cover the power tool to protect it from dust or moisture.
Store the operating manual with the power tool.
When storing for a long period of time
1. Empty the fuel tank and run the carburettor empty.
2. Unscrew the spark plug.
3. Approx. Pour approximately 20 ml of clean engine oil through
the spark plug hole into the cylinder.
4. Pull the starter rope out slowly so that the oil distributes itself
in the engine and screw the spark plug back in.
5. Remove all dirt, deposits and dust from the engine and the
cylinder head ridges.
6. Clean the air filter or replace it if it is very dirty.
7. Store the power generator securely in a dry place that is
inaccessible to children.
8. The unit may not be stored in the open.
9. Cover the unit and the engine to protect against dust and
store in a clean, dry place.