Gude Expert Power Control 8042 Series Скачать руководство пользователя страница 59

Страница: 59 / 96

Expert Power Control 8042

Configuration

3.8.1

GSM General

It is still possible to use and configure a voice call in this device, but it is not re-

commended and is not an official part of the scope of services of the device. This fea-
ture will be removed in a later firmware update.

Enable GSM: Activates the built-in GSM module

SIM PIN: Switches the PIN request of the SIM card on. A wrong Pin leads to a blocking
of the SIM card. You

cannot

change the PIN of the SIM card via this menu option.

My phone number: Please enter here the phone number of the inserted SIM card

Admin SMS number: All device changes are sent via SMS to this mobile number.

Enable admin GSM status information: When active, all GSM status changes are sent
via SMS to the Admin.

Enable admin GSM E-mail: When active, all GSM status changes are sent via E-Mail
to the Admin. The e-mails are sent via the SMS to email gateway.

Admin E-mail: Email address to which the GSM messages are sent.

Enable DTMF/SMS access codes: When activated, the Mastercode or Portcode is
needed to switch a port.

Master code: Sets the GSM Mastercode.

3.8.2

GSM Misc

It is still possible to use and configure a voice call in this device, but it is not re-

commended and is not an official part of the scope of services of the device. This fea-
ture will be removed in a later firmware update.

Содержание Expert Power Control 8042 Series

































































































Результаты поиска

Содержание Expert Power Control 8042 Series

Отзывы:

Gude Expert Power Control 8042 Series, Руководство пользователя, Страница: 59 / 96

Результаты поиска

Содержание Expert Power Control 8042 Series

Отзывы: