Gude 94375, Перевод оригинальной инструкции

Страница: 15 / 106

Assembly GH 2800 #94375 (Fig. F/G)
Attention! Turn off and unplug the
appliance before maintenance, cleaning
and assembly. The same procedure
applies to damaged, cut or tangled cable.
Keep power supply voltage: power supply
voltage must correspond to data on the
appliance product label.
Small conductor size of the extension
cable significantly reduces power output of
the appliance. For cables up to 25 metres,
minimum cross section is 3 x 1.5mm², for
cables over 25 metres, minimum cross
section is 2.5mm². Attention! The
extension cables not corresponding to the
requirements must not be used. The
extension cable, plug and socket must be
water-proof and approved for outdoor
application.
Cable connections must be dry and must
not rest on ground.
If a cable drum is used, it must be
unreeled.
For GH 2800 P #94375, proceed as
follows:
(Fig. F, G)
•
Unpack the appliance (Fig. F/2 and
F/3)
•
Take the collection box and attach
legs to the appliance (Fig. F/4 and
F/5)
• Attach the carriage and transport
wheels (Fig. F/6 and F/7).
• Put the appliance body on the base
(Fig. G/8) (adhere to Fig. G/8-1
and G/8-2 ).
• Now, attach the appliance to the
base. (Fig. G/9)
• Put the collection box under the
appliance (Fig. G/10) and secure
by the collection box clamping
lever (G/10-1 a G/10-2). Attention!
The appliance does not operate
without clamping!
Operation
Always put the appliance on solid and leveled surface. Do
never tilt or move the appliance if it is on and running.
Attention! The engine runs down after turning off.
Remove soil from the root balls and avoid penetration of
foreign objects such as stones, glass, metals, plastic
materials or textiles in the filling hopper and thereby to the
appliance, cutting roll; the appliance may get damaged.
The filling hopper must be empty.
Turning on
Press green Start pushbutton (Fig. A/3) or
(Fig. E/2)
Turning off
Press red Stop pushbutton (Fig. A/3) or
(Fig. E/2)
Safety feature against repeated running up
The safety feature against repeated running up prevents
sudden engine start after power supply failure.
Reverse operation
Press and hold the reverse operation button (Fig. A/4),
(Fig. A/4a) and depending on your model, press also
green Start button (Fig. A/3) or (Fig. E/2), the cutting roll
then rotates in reverse direction and releases the clogged
material.
Overload safety feature
If the appliance is exposed to excessive load (e.g. clogging
of cutting roll), the appliance halts after several seconds.
Work instructions
Material supply
Insert the shredded material only, the rotating cutting roll
will draw it in automatically.
• Insert such quantity of material not to clog
the hopper.
•
Do not shred soft waste without solid
consistency but compost it directly.
• Make sure the shredded material exits to the
collection box or bag without any
restrictions - danger of clogging!
• Best results are achieved if you shred fresh
branches shortly after cutting.
Adjustment of pressure plate
The pressure plate is calibrated by the manufacturer and
requires no adjustment before first commissioning.
Adjustment of the pressure plate is required in case of
wear, e.g. when the branches wedge in chain each other
and they can not be shredded correctly.
In this case proceed as follows:
Turn the engine on and slowly rotate the adjustment knob
(Fig. A/9 or Fig. E/6) or Fig. H/13 clockwise to hear slight
friction. The cutting roll sharpens the pressure plate to
correct distance. Adjust the plate so that it is not worn too
early.
Identification
Product safety:
The product complies with
relevant EU standards