GST GST301 Скачать руководство пользователя страница 17

Страница: 17 / 18

GST301 Extinguishing Control Panel

Installation and Operation Manual

Page 15

Press “Evacuate” key to start the sounder outputs. This operation is controlled
by “Control Enable” switch.

7) Isolation/De-isolation operation

In case of false-alarm and fault, if the problem cannot be removed immediately,

the faulty zone can be logically isolated in order to avoid false-release and

noises. After the problem is solved, De-isolate to resume the functions. The

Isolation/De-isolation operation is available for Zone1, Zone2, AUX Zone and

the Cylinder. Pressing the corresponding “ISO1

～

ISO4” key to change the

isolation condition. This operation is controlled by “Control Enable” switch.

8) Standby cylinder output

To ensure fire protection, there should be 2 sets of gas cylinders in field. In

case of fault with the primary (discharge, low pressure or other problems),

switch the output to standby terminal.

Note: Only the circuit in use is

monitored.

VII Troubleshooting

The panel itself is able to check and judge fault. If there is any short or broken circuit

with wiring of a certain zone, the panel will light corresponding fault indicator, and output

fault remote signal. If it still cannot work normally or still alarm fault, please contact GST

technical support personnel.

VIII Cautions



If the cylinder

’

s output or the sounder

’

s output is set as a normally-open or

normally-closed type, the corresponding current fuse must be removed!



‘ISO4’ operation is only valid for gas release actions caused by emergency
start button and detection zones. The “START” key on the panel is not under

control. That means even if the output is isolated, gas release can still be

active by the “START” key.

So, only when

“ISO

”

is active and

“C

ontrol

Enable

” is Off, will gas release

output be completely inhibited.



If there is any serious internal error during self-test, the panel will show

flashing

‘

’

on its front panel and start the fault remote output. In this case,

repair must be done.



The panel must be properly grounded to ensure safety.



The panel must be maintained or repaired by authorized and skilled person.

Содержание GST301



















Результаты поиска

Содержание GST301

Отзывы:

Бренды по названию

Популярные бренды

GST GST301, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GST301

Отзывы:

Бренды по названию

Популярные бренды