GSI Group PNEG-1020 Скачать руководство пользователя страница 10

Страница: 10 / 48

PNEG-1020 Bin Sweep Auger

Safety

Prepare for Emergencies

Be prepared if fire starts.

Keep a first aid kit and fire extinguisher

handy.

Keep emergency numbers for doctors,

ambulance service, hospital, and fire

department near your telephone.

Keep Emergency Equipment
Quickly Accessable.

Wear Protective Clothing

Wear close fitting clothing and safety

equipment appropriate to the job.

Safety glasses should be worn at all times

to protect eyes from debris.

Wear gloves to protect your hands from

sharp edges on plastic or steel parts.

Wear steel toe boots to help protect your

toes from falling debris.

A respirator may be needed if a hog house

has poor ventilation. Waste fumes can be

toxic.

Remove all jewelry.

Tuck in any loose or dangling shoe strings.

Long hair should be tied up and back.

Wear hard hat to help protect your head.

Eye Protection

Gloves

Steel Toe Boots

Respirator

Hard Hat

Содержание PNEG-1020

















































Результаты поиска

Содержание PNEG-1020

Отзывы:

Похожие инструкции для PNEG-1020

Бренды по названию

Популярные бренды

GSI Group PNEG-1020, Руководство по установке и эксплуатации

Результаты поиска

Содержание PNEG-1020

Отзывы:

Похожие инструкции для PNEG-1020

Бренды по названию

Популярные бренды