manualshive.com logo in svg

Gruner F5J, Инструкция по сборке, Страница: 34 / 38

Поделиться
Скачать
Gruner F5J Скачать руководство пользователя страница 34

62

Fuselage

●

First, cover the sidewalls of the fuselage

●

Cut covering for the sides of the fuselage with a 5 mm overlap at the top and bottom and
a 2mm overlap/projection on the front. Iron the covering on including the overlap on the
sides and the front. Slit and iron covering to fit in wing saddle and hatch opening (top left)

●

WARNING:

If the elevator is to be glued in place, do not cover the joining surface on 

the

 

fuselage.

●

Fuselage bottom covering. Cut the covering so that an overlap of approximately 35 mm 
is given. Ironing on the covering and overlaps.

●

Cover the Canopy and battery hatch. Cut the film with an overlap of 35 mm and iron on.

●

For the battery hatch cut the covering with a maximum of 2 mm overlap and iron on.

63

Sheet 72.12
Part F82

●

Cover the servocover. The openings for the servo arm and screwholes can be cut with
a hot soldering iron. You can also cut the holes for the servo hatch mounting screws
and the oblong hole in the battery hatch.

●

Cut out the openings for the servos with 2 mm overlap and iron down the overlap.

●

Cut the covering flush to the slot in the center rib to make room for the wing anchorage F82.

●

Glue the wing anchorage F82 by stacking all three parts so they align well (thick CA).

●

Glue the wing anchorage F82 and secure with tape (90 minutes epoxy).

WARNING:

Pay attention to ensure there is a good adhesive bond in the wholearea.

The

 

top of the front pin has to touch the leading edge.

Содержание F5J







































Отзывы:

Нет отзывов