Gruner F5J Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 38

Gruner F5J Скачать руководство пользователя страница 15

25

Sheet 72.01
Parts R53a,
R53b

Sheet 72.14
Part R54

●

Glue the doubler of the battery flap R53.2 exactly centered on the part R53.1 (thick CA).

●

Glue the siderails, R54 on both sides of R53 (thick CA).
The battery hatch cover should fit easily into the fuselage cutout.

26

Sheet 72.01
Parts R49-
R52

Long parts
bundle
Part R56

Small parts
Part R65

●

Glue the front fuselage skin R52 (picture 1) (thick CA).

●

Glue the top sheeting R50 and R51 together at the abutting edges (pict. 2) (thick CA).

●

Glue the holder R49 front flush and centered on the sheeting R50 (pict. 3) (thick CA).

●

The hatch cover can be retained by a either wire or magnetic closure. For the wire
closing, use a short piece of guide tube R29. For the magnetic closure, glue a bar
magnet R65 in the cap holder (picture 3). The magnet in the battery compartment
should only be glued after covering with covering film — and verifying the polar
direction. (5 minutes epoxy)

●

Slide the hatch cover in the fuselage. Leaving a 0.5 mm gap between the hatch cover
and R50, glue R50 and R51 to the fuselage (thick CA).

«
...
13
14
15
16
17
...
»

Содержание F5J







































Отзывы:

Нет отзывов