Gruner F5J Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 38

Gruner F5J Скачать руководство пользователя страница 18

31

Sheet 73.03
Parts F7F9,
F11

Sheet
73.11
Part
F10

Long parts
bundle
Part F1

●

Dryfit the rib combination F6/F4/F6 and all ribs labeled F7, F8, F9 and F11 onto the
spar tube F1, according to the plan.

●

Insert the servo frame F10 between the ribs F8 and F9.

32

Sheet 73.10
Part F12

●

Pin the trailing edge F12 over the plan.

●

Gently push the ribs down into the recesses of the trailing edge and align according to

plan.

WARNING:

The flat base of the ribs must rest their entire length on the building

board.

●

Align the ribs vertically and glue to spar tube F1 and to trailing edge F12 (thin CA). Use
thick CA to fill the gaps if void can still be seen between the spar tube and the ribs. The
ribs must be glued around the entire circumference of the spar (thick CA).

●

Using a small round file, shape the spar cutouts in the two rib combinations F6/F4/F6
to match the angle template W1, ensuring to shape one lefthanded and one right-
handed cutout.

●

Slide the F6/F4/F6 rib combinations and glue to spar tube F1 using the angle template
W1 for proper alignment (thin CA).

«
...
16
17
18
19
20
...
»

Содержание F5J







































Отзывы:

Нет отзывов