background image

English (GB)

12

If the inlet is located too high relative to the liquid level or with a 
high flow velocity, it may cause entrainment of air and the 
formation of eddies in the liquid when entering into the pit. Air 
entrained in the liquid tend to remain inside the pump impeller, 
where the centrifugal force makes it accumulate around the 
impeller hub. This may lead to increased power requirements and 
lowered performance and efficiency. The risk of cavitation and 
pump vibrations also increases. If the amount of air in the pump is 
very high, the pump may stop operating.

Fig. 21

Avoided location of retrofitted inlet

5. Installing the pump(s)

For installation and startup of the pump(s), see the installation 
and operating instructions for the pump.

6. Installing the level switches

See the installation and operating instructions for the level control 
system.
When installing the level switches, observe the following points:
• To prevent air intake and vibrations in the pump, the stop level 

switch must be fitted in such a way that the pump is stopped 
before air is sucked into the pump.

• In the case of one-pump operation, the start level switch must 

be installed in such a way that the pump is started at the 
required level; however, the pump must always be started 
before the liquid level reaches the lower edge of the bottom 
inlet pipe.

• In the case of multipump operation, the start level switches 

must be installed in such a way that pumps are started before 
the liquid level reaches the lower edge of the bottom inlet pipe.

• The high-level alarm switch must always be installed about 

100 mm above the start level switch; however, the alarm must 
always be given before the liquid level reaches the inlet pipe.

For further settings, see the installation and operating instructions 
for the level switch selected.

TM

07

 12

48

 12

18

DANGER
Crushing hazard

Death or serious personal injury
- Do not stand under or close to a suspended load.

Use only certified, CE marked lifting chains.

Lower the pump carefully into the pit in order to avoid 
damage to the pump and the pit.

DANGER
Crushing hazard

Death or serious personal injury
- Make sure the lifting equipment is rated for the 

weight of the pump and is approved and 
maintained according to local regulations.

Chains supplied by Grundfos are marked with 
maximum load and production date.
Do not exceed the maximum load.
Maintain the chain according to local regulations. We 
recommend that you check chains and shackles 
supplied by Grundfos at least once a year for cracks, 
corrosion or other irregularities. If you find any 
defects, replace the chain or shackles.

CAUTION
Electric shock

Minor or moderate personal injury
- Make sure the float switches are connected 

properly and that the cables are not bent or 
sharply pinched.

If the pit is equipped with an AUTO

ADAPT

 

-controlled 

pump, an external level controller is not needed.

Содержание PS.G Series







































Отзывы: