GrowSpan 106201 Скачать руководство пользователя страница 45

Страница: 45 / 49

GROWSPAN

™

ROUND PREMIUM GREENHOUSES

Revision date: 01.10.19

106201_02_03_04

H-CHANNEL

INST

ALLA

TION INSTRUCTIONS

The new H-channel design requires installation of flat side facing out with channel side toward building. Some diagrams and

photos in this document may show installation of

original

H-channel with channel side facing out. Design of new H-channel

does not allow

channel-side out installation.

Use the diagrams on this page to install H-channel with flat side facing out.

ATTENTION:

Use only 1-1/2"

Tek screws to

attach H-channel to building frame.

Do not use

shorter screws. They will not hold. Do not use washers on T

ek screws when installing the

113236Z096 H-channel.

ATTENTION:

Install all twin-wall polycarbonate panels with UV

-protected side toward the sun.

-protected side toward sun.

Install 1-1/2"

Tek screws through

H-channel into building frame.

H-Channel

Center Groove

Flat side toward the sun.

Flat Side

Channel

ASSEMBL

Y NOTE:

Install

Tek screws using a clutched

drill driver running approximately 750 RPM while applying approximately 50 lbs of force.

Do not use an impact driver to install T

ek screws!

Содержание 106201


















































Результаты поиска

Содержание 106201

Отзывы:

Бренды по названию

Популярные бренды

GrowSpan 106201, Инструкция по эксплуатации

Результаты поиска

Содержание 106201

Отзывы:

Бренды по названию

Популярные бренды