manualshive.com logo in svg

GrowSpan 106201, Инструкция по эксплуатации

Поделиться
Скачать
GrowSpan 106201 Скачать руководство пользователя страница 17

17

GROWSPAN

™

 ROUND PREMIUM GREENHOUSES

Revision date: 01.10.19  

106201_02_03_04

INSTALL THE END WALL FRAME (continued)

Space below reserved for customer notes.

7.  Repeat steps to assemble remaining end frame. 

 

ATTENTION:

 End framing for back end wall is  

identical, but will not include a door. 

8.  After end frames are assembled, return to each band 

clamp and pipe splice of base tubes and verify that a 

Tek screw is installed. Install a Tek screw if needed.

9.  Continue by installing polycarbonate end wall panels.

6.  Place door header tube on top of installed door. Verify 

header is tight against jambs and is level. Secure 

header to jambs using Tek screws.

Tek

screws

ASSEMBLY NOTE:

 Install Tek screws using a clutched 

drill driver running approximately 750 RPM while applying 

approximately 50 lbs of force. 

Do not use an impact driver to install Tek screws!

Содержание 106201


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды