Groen C/2-20G, Руководство оператора

Страница: 19 / 25

OM-CC-G and C/2-G
19
Cleaning
To keep your Convection Combo™ in proper operating condition and to make the cleaning process easier,
cleaning should be a daily activity.
A. Suggested Tools and Cleaners
1. Mild detergent
2. Stainless steel exterior cleaner such as
Zepper®
3. Steam generator de-liming agent, such
as
Groen Delimer Descaler, (P/N
114800) Lime-A-Way® or an equivalent.
A liquid de-liming agent will be easier to
use than crystals or powders.
See the
warning about chlorides below .
4. De-greaser, such as EncompasS®, Groen
Degreaser , Malone 34®, Puritan
Puribrute®, or Con-Lie®
5. Cloth or sponge
6. Plastic wool or a brush with soft bristles
7. Spray bottle
8. Measuring cup
9. Nylon pad
10. Towels
11. Plastic disposable gloves
B. PROCEDURE
1. Exterior Cleaning
a. Prepare a warm solution of the mild
detergent as instructed by the supplier.
Wet a cloth with this solution and wring it
out. Use the moist cloth to clean the
outside of the unit. Do not allow freely
running liquid to touch the controls, the
control panel, any electrical part or any
open louver.
b. To remove material which may be stuck to
the unit, use plastic wool, a fiber brush, or
a plastic or rubber scraper with a
detergent solution.
c. Stainless steel surfaces may be polished
with a recognized stainless steel cleaner
such as Zepper®.
d. For glass surfaces, use a mild detergent
without abrasives or a high quality
glass/surface cleaner with a clean cloth or
sponge. Do not spray hot glass with water
or chemicals. This could cause the glass to
break from thermal shock.
e. Use a mild soap without abrasives and warm
water to clean the door gasket. DO NOT
use caustic oven cleaners on the door
gasket, as this will damage it.
PRECAUTIONS
WARNING
DISCONNECT THE POWER SUPPLY
BEFORE CLEANING THE OUTSIDE OF
THE UNIT.
K E E P W A T E R A N D C L E A N I N G
SOLUTIONS OUT OF CONTROLS AND
ELECTRICAL COMPONENTS. NEVER
HOSE OR STEAM CLEAN ANY PART OF
THE UNIT.
BE CAREFUL CLEANING THE TOP FLUE
COVER AND THE OVEN TOP. BOTH
AREAS MAY BE VERY HOT.
DON’T MIX DE-LIMING AGENTS (ACID)
W I T H
D E - G R E A S E R S ( A L K A L I )
ANYWHERE IN THE UNIT
AVOID CONTACT WITH ANY CLEANERS,
DE-LIMING AGENT OR DE-GREASER AS
RECOMMENDED BY THE SUPPLIER.
MANY ARE HARMFUL. READ THE
W A R N I N G S
A N D F O L L O W T H E
DIRECTIONS!
EVEN WHEN THE UNIT HAS BEEN SHUT
OFF, DON’T PUT HANDS OR TOOLS INTO
THE COOKING CHAMBER UNTIL THE FAN
HAS STOPPED TURNING.
DON’T USE ANY CLEANING OR DE-
LIMING AGENT THAT CONTAINS ANY
SULFAMIC AGENT OR ANY CHLORIDE,
INCLUDING HYDROCHLORIC ACID (HCl).
TO CHECK FOR CHLORIDE CONTENT
SEE ANY MATERIAL SAFETY DATA
SHEETS PROVIDED BY THE CLEANING
AGENT MANUFACTURER
.
UNIT MAY BE HOT. TAKE PRECAUTIONS
TO PREVENT CONTACT WITH HOT
SURFACES.
To clean the cooking chamber and/or de-lime the steam
generator of the CC10-G or C/2-20G, a special
sequence of operations (the Clean Cycle) has been
programmed into the Convection Combo™ computer.
To run this automatic Clean Cycle for cleaning, de-
liming or both actions at the same time, follow the
instructions outlined on the following page.
IMPORTANT
DO NOT USE ANY METAL MATERIAL (SUCH AS METAL SPONGES) OR METAL IMPLEMENTS (SUCH AS A SPOON, SCRAPER OR
WIRE BRUSH) THAT MIGHT SCRATCH THE SURFACE. SCRATCHES MAKE THE SURFACE HARD TO CLEAN AND PROVIDE PLACES
FOR BACTERIA TO GROW.
DO NOT USE STEEL WOOL , WHICH MAY LEAVE PARTICLES IMBEDDED IN THE SURFACE WHICH COULD
EVENTUALLY CAUSE CORROSION AND PITTING.