Groen C/2-20G, Руководство оператора

Страница: 16 / 25

OM-CC-G and C/2-G
16
h. Press the numbered touch pads to set the
cooking time. The time will appear in the
Time/Status display. If you enter the wrong
number, press the
CLEAR touch pad to
erase the time from the display, and enter
the time again.
i. When the correct cooking time has been
entered, press the
START pad. The colon in
the Time/Status display will blink and the
time will count down the cooking time. (The
unit must be
READY before the timer can
count down.)
j. If you open the door during the cooking
period, steaming and the timer will stop (but
will not reset). When you close the door,
steaming and timing will resume.
WARNING
WHEN YOU OPEN THE DOOR STAY AWAY
FROM ANY STEAM COMING OUT OF THE UNIT.
STEAM CAN CAUSE BURNS.
k. When the timer reaches zero, it stops steam
generation and sounds a beeper. Water in
the steam generator stays at its standby
temperature (200
o
F - 93
o
C). On older
models, the beeper will sound until the door
is opened or
CLEAR is pressed.
l. Carefully open the door. If the food is
cooked, remove the pans using hot pads or
oven mitts to protect your hands.
m. After the display has counted down to zero,
opening the door or pressing CLEAR once
will reset the display to the time that was last
used. Pressing
START will repeat the cook
cycle. If the same cooking time will be used,
you only need to press the number keys
when you first set that time.
n. After the Time/Status display has counted
down to zero, you can reset the time to zero
by either (1) opening the door
and pressing
CLEAR or pressing CLEAR twice. A new
cooking time may then be set by using the
number keys.
2. Oven Mode
a. To use the Convection Combo™ as a
convection oven, switch on the electric
power by pushing the
ON touch pad. (If the
SERVICE light comes on when you turn on
the power, see the Troubleshooting section).
If the door is closed and the cooking
temperature is above 250
o
F (120
o
C) the fan
will begin to operate.
b. If the power is already on, and there is a
number in the Time/Status display, press
CLEAR one or more times to reset the time
to zero.
NOTE: You cannot change operating modes
while the timer is running
c. The unit will power up in the mode in which it
was last used. Because of this, the indicator
light for that mode will be lit. If the unit is not
already in the Oven Mode, press the
OVEN
touch pad. The OVEN light will come on and
the oven fan will operate.
d. Use the Temperature Control Knob to set
the desired cooking temperature between
200
o
and 575
o
F (93
o
to 300
o
C). NOTE:
Maximum temperature is limited to 500°F
when the either the optional probe or
optional hold mode is in use. The
temperature will appear in the Cook display.
Unless the cooking chamber is already at or
above the selected temperature, the unit will
start heating and the
WAIT light will come
on.
e. If the unit was recently used at a
temperature 15
o
F (8
o
C) or more over the
selected temperature, the HOT and WAIT
lights will come on. The unit can be cooled
quickly to the desired cooking temperature
by leaving the door open or following the
Fast Cool procedure described near the end
of this section (Paragraph 4).
f. The READY light will indicate when the oven
is at the desired temperature.
g. Load the food into the pan or pans in a
uniform layer.
h. The Convection Combo™ will operate in
Oven Mode with the timer either on or off. If
you want to time cooking, press the
numbered pads in the Time/Status portion of
the control panel to set the cooking time.
The time will appear in the Time/Status
display . If you enter the wrong number,
press
CLEAR to erase the time from the
display, and reenter the time. Remember
that the timer
does not control the unit in
the Oven Mode.