Model FDD2500
Page 5
Programming Machine from Touchpads
Tools Required:
None
MACHINE PROGRAMMING: The machine operating parameters can be changed from the touchpad and LCD display
without opening up the machine. (See illustration below).
To enter
Programming Mode:
Press and hold (>) and (+) at the same time for approximately 5 seconds.
Tip
: Use the eraser end of two pencils to press the buttons if you are having difficulty entering programming mode.
To
Exit
programming mode at anytime:
• Wait 20 seconds without pressing a button.
• The display will prompt “Exit?”
• Press (+) or (-) to toggle between YES and NO.
•
After selecting YES, you MUST press (>) to SAVE changes
, or wait for ready message and machine
will exit without saving.
Tip:
To verify changes successfully save, re-enter programming mode and check settings.
1) Press (>) to select
Language. (1A)
Press (+) to choose English, Spanish, German, or French.
2) Press (>) to set the
Time
of day on the machine.
Press (+) or (-) to change the time.
3) If password is activated, enter password now.
a) Press (+) to enter first number.
b) Press (>), then (+) to enter second number.
c) Press (>), then (+) to enter third number.
NOTE: The default password is
“111”
. If the password has been changed and forgotten, press
“I/O”
and “
+”
at the
same time to proceed.
4) Press (>) to change
Password
settings.
(2B)
Press (+) or (-) to toggle between ON (enable password) and OFF (disable password).
If ON is selected, press (>) to change password.
a) Press (>) to enter new password. (following steps 3 a, b, c)
b) Press (>) to confirm new password. (following steps 3 a, b, c)
5) Press (>) to program
Dispense Settings
. (to change
Portion Sizes
)
(2E)
(For FDD2500-**-3A models only)
a) Press (+) for message “Select Dispense Button”.
(5A)
b) Press the dispense button for the dispense head you wish to adjust the settings. LCD will display L, M,
or R for left, middle, or right dispense head to acknowledge your selection.
c) Once the dispense head is selected, press (+) or (-) to change the amount of time (portion size) for the
beverage being dispensed.
6) Press (>) to change
Whipper Settings. (5A1)
a) Press the dispense button for the dispense head you wish to adjust the settings. LCD will display L, M,
or R for left, middle, or right dispense head to acknowledge your selection.
b) Once the dispense head is selected, press (+) or (-) to toggle between ON (turn whipper ON) and OFF
(turn whipper OFF).
7) Press (>) to return to
Dispense Settings. (2E)
Repeat steps 6 & 7 for remaining heads.
8) Press (>) to modify
Drink Strength. (7A)
a) Press (>) to Select a Dispense Button.
(7B)
b) Press the dispense button for the dispense head that you want to change the drink strength for.
c) Press (+) or (-) to modify the auger speed which changes the drink strength (0-100% of maximum auger
speed in 1% increments).
Note:
A faster speed will result in a stronger drink and a slower speed will result in a weaker drink.
PROCEED
POWER ON/OFF
(STANDBY)
INCREMENT UP
INCREMENT DOWN
Содержание FDD2500-1-3A-B
Страница 20: ...Page 20 Model FDD2500 FDD2500 Hopper Assembly ...
Страница 32: ...Page 32 Model FDD2500 Wiring Schematic within Door for models FDD2500 1 M B FDD2500 3 M B ...
Страница 34: ...Page 34 Model FDD2500 ...
Страница 35: ...Model FDD2500 Page 35 ...
