10
TECHNICAL DATA
ENGINE:
9.16 - BRIGGS & STRATTON VANGUARD OHV 16 HP (13 Kw) twin-cylinder, internal
combustion, 4 strokes. 9.21 - BRIGGS & STRATTON VANGUARD OHV 21 HP (15.5 Kw) twin-cylinder,
internal combustion, 4 strokes
HOURLY CONSUMPTION:
3,5 lt/h.
STARTER:
electric. 12v battery.
GEARBOX:
hydrostatic transmission.
DIFFERENTIAL:
with locking device.
CLUTCH:
for P.T.O., electromagnetic.
SPEED:
continuously variable from 0 to 9 Km/h + reverse speed from 0 to 4 Km/h.
TYRES front:
13 x 50 - 6;
rear:
17 x 8.00-8.
BRAKES:
front brakes: drum – service brakes: hydrostatic – parking brakes: disk.
SEAT:
sprung and adjustable.
CUTTING DECK:
rear/side discharging.
CUTTING SYSTEM:
rotating with one blade.
CUTTING WIDTH:
900 mm.
CUTTING HEIGHT:
from 30 mm. to 90 mm: 4 different cutting positions and 1 transfer position.
HOURLY CUTTING CAPACITY:
6000 m_/h (approximate).
FUEL TANK:
13 lt,
- EMERGENCY SUPPLY:
3 lt.
IMPLEMENTS:
drawbar, garden wheels kit.
SIZE: Lenght:
1.780 mm
- Width:
990 mm
- Height:
940 mm
WEIGHT:
9.16 - kg. 293. 9.21 – kg. 305.
PUTTING THE MACHINE INTO SERVICE
1) Check that the machine has not been damaged in transit.
2) Check the oil levels of the engine, hydrostatic transmission and final drive.
3) Check the tyre pressure:
1 BAR front wheels 13 x 50/6
1.5 BAR rear wheels 17 x 8.00-8.
4) Check the battery voltage; it must be at least 12 Volts. Charge if necessary.
If the battery has been supplied dry with the acid separate, to put it into service proceed as follows:
1) Add the acid and wait 2 hours.
2) Charge the battery with a battery charger set at 12 Volts on slow charge for 2 hours.
Caution; failure to follow this rule may cause deterioration of the battery and acid leaks during operation.
IMPORTANT!!!
During assembly take care not to reverse the polarity of the battery.
BATTERY - CAUTION!
The gases released by the battery are explosive, keep it away from naked lights or sparks. Check the liquid
level periodically and keep the terminals lubricated with Vaseline grease.
RUNNING IN - CAUTION!!
Change the engine oil and filter after the first 30 working hours.
Change the wheell reduction oil after the first 130 working hours (80W90). Quantity 1,9 lt. (Fig. 11/A).
Check that there are no oil leaks or slack screws, especially those which fix the blade, the steering and
the wheels. Adjust the tension of the hydrostatic transmission belts.
INSTRUCTIONS FOR USE
Before starting up the engine, always check that:
– the engine oil level is correct (Fig. 2);
– the oil in the hydraulic motor is at the correct level (Fig. 3);
– the travel lever is in the idle position (2, Fig. 1/B);
– the engine cooling intake grilles are clean (Fig. 5);
– air filter is clean (Fig. 6).
– the mowing plate is clean;
Содержание Climber 9.16
