Greyline Instruments PSL 5.0 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 44

background image

Page 32

PSL 5.0 Pump Station Level Controller

SENSOR INTRINSIC SAFETY
(OPTION ISB)

When connected through Intrinsic Safety Barriers, Greyline PZ** Series sensors are certified for
installation in a hazardous location rated:

Class I, Groups C,D

Class II, Groups E,F,G

Class

III

The Intrinsic Safety Barrier may be ordered with the Greyline instrument and is supplied mounted in the
Greyline instrument enclosure. Replacement barrier fuses (Part No. ISB- 011239) may be purchased
separately. The instrument enclosure containing the ISB Intrinsic Safety Barrier must be installed in a
non-hazardous location.

«
...
30
31
32
33
34
...
»

Содержание PSL 5.0













































Отзывы:

Нет отзывов

Похожие инструкции для PSL 5.0

Бренд: K&K Страницы: 6

Бренд: Ickle Bubba Страницы: 23

ESSENSSE NEO COMFORT

Бренд: 2VV Страницы: 21

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: Calsense Страницы: 74

Бренд: UCS Страницы: 4

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: janitza Страницы: 58

FUTERA XLF Series

Бренд: RBI Страницы: 128

Бренд: RBH Access Technologies Страницы: 36

Бренд: S&C Страницы: 11

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 19

Бренд: WAM Страницы: 62

Бренд: walimex Страницы: 7

Бренд: Walchem Страницы: 2

Бренд: Walchem Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды